COBHAM SOLO4 Spezifikationen Seite 76
- Seite / 99
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
76
13.3 Engineering Data Page
The Engineering Data page contains antenna input spectrum plots,
along with GPS, temperature and video lock data received from the
transmitter.
13.4 GPS Overlay
The GPS Overlay is a small three lines of text over the top left of the
video. The text contains a time (UTC), date, longitude, latitude and fix
type as extracted from GPS data from a transmitter.
If “Data Disabled” is shown the Data configuration option n
eeds to be
turned On to receive transmitter data. If Data is disabled this page will
not appear whilst changing page via the front panel.
Note: For GPS data to appear on the OSD several conditions need to be met. A
compatible GPS receiver with NMEA output should be connected to the data port of a
transmitter. The transmitter must have Data enabled and the correct Baud rate set (usually
4800 for NMEA), and the receiver must have Data enabled.
14:06:59 24/07/09
50 52.136 N 3D
1 15.205 W Fix
Engineering Data
----------------
A -65 SNR:25
|
| WWWWWWWW
| W W
|WWW WWW
----------------
B -130 SNR:
|
|WWWWWWWWWWWWWWWW
|
|
----------------
Transmitter:
GPS 14:06:59
3D 50 52.136 N
Fix 1 15.205 W
Case : 49’C
Video: Lock
Antenna input frequency
spectrum plots. Input level
is shown at the top left of
each plot and SNR is
shown if available.
Antenna inputs A and
B are shown here. If C
and D are available
either A and B, or C
and D will be shown
depending on settings.
When setup correctly NMEA
GPS data can be collected
from a transmitter, and
coordinates are displayed
with their UTC time stamp.
If the time is not updating
frequently or the fix type
shows “No Fix” then the
GPS coordinates are the last
received at the time shown.
If “Data Disabled” is shown
the Data configuration option
needs to be turned On to
receive transmitter data.
If estimated case
temperature or video lock
status is received from a
compatible transmitter this
will be shown here.
- SOLO2 and SOLO4 1
- Users’ Manual 1
- 1 Table of Contents 2
- 2 Change History 4
- • Advanced operation 5
- • Technical reference 5
- 4 Introduction 6
- 5 Warranty and Support 7
- 5.1 Warranty Cover 7
- 6.3 CE marking 8
- S-Band 10
- Made in the UK 10
- Controls 12
- Cables and Connections 15
- • Control 3m 16
- • DC Power 2m 16
- DC Power 17
- Video and Audio 17
- Antennas 18
- • Vehicle based applications 19
- Connections 22
- Square down-converter 24
- Video Output Connection 28
- • Current Draw – 0.9A at 12V 29
- • Current Draw – 1.0A at 12V 29
- Control Cable 30
- Data Connection 30
- Installation Notes 30
- 7.4 Powering on the System 31
- Diagnostic On Screen Display 32
- Using the SOLBAT 34
- Charging the SOLBAT 34
- Amplifier Connection 35
- DC Power and Control Cable 36
- • Vehicle applications 37
- • Aircraft applications 37
- • Long Range fixed links 37
- RF Connection 38
- 8 Advanced Operation 41
- Output Frequency (MHz) 43
- Bandwidth Mode 44
- Default Transmit Mode 44
- Scrambling 44
- File Options 44
- Advanced TX Controller Window 45
- Modulation Bandwidth 45
- Modulation Output 45
- Narrow Band FEC 46
- Narrow Band Guard Interval 46
- Narrow Band Modulation 46
- DVB-T Service Name 46
- DVB-T FEC 46
- Video Bitrate 48
- Horizontal resolution 48
- Audio Encoder 48
- Audio Input Level 48
- Unit Name 48
- Input Frequency (MHz) 52
- Service Name 52
- Descrambling 52
- Advanced RX Controller Window 53
- Narrowband / DVB-T 53
- Input Frequency 53
- FPGA Version (Status Only) 57
- Chaining 57
- 9 NETSTREAM IP Output Option 59
- 9.1 General Info 59
- 9.2 Streamer 59
- 9.3 Web Server 59
- 10 Software Decoder 62
- 10.1 General Information 62
- 10.3 Encrypted Streams 65
- 10.4 Main Decoder Window 67
- Enable audio 68
- Close window 68
- 11 Fault Finding 71
- 11.1 Indicated Faults 71
- 11.2 Fault Symptoms 72
- 12 LED Indicators 73
- 13.1 Input Status Page 74
- 13.2 RF Advanced Page 75
- 13.3 Engineering Data Page 76
- 13.4 GPS Overlay 76
- 13.5 Frequency Scan Page 77
- Quick Scanning Stage 78
- Service Scanning Stage 78
- Completed Scan 79
- Front Panel Control 80
- Control Commands 81
- Original OSD Mode 82
- OSD Timeout 83
- 15 Control Protocols 86
- 15.5 Receiver Command List 94
- 16 Default Configurations 98
Verwandte Produkte und Handbücher für Empfänger COBHAM SOLO4
Empfänger COBHAM NanoVue Bedienungsanleitung
(51 Seiten)
(51 Seiten)
Empfänger COBHAM Messenger VETA Handbuch
(31 Seiten)
(31 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern